Jeepin.com Forums - Project CRD MJ:

Page 2 of 7

Last »

Show 40 post(s) from this thread on one page

Jeepin.com Forums (https://www.jeepin.com/forum/index.php)

- Jeep Talk (https://www.jeepin.com/forum/forumdisplay.php?f=2)

- - Project CRD MJ: (https://www.jeepin.com/forum/showthread.php?t=61)

Sir Sam

11-04-2017 01:39 PM

old post quoted:

Quote:

Originally Posted by Sir Sam

Sir Sam

11-04-2017 01:39 PM

old post quoted:

Quote:

Originally Posted by Sir Sam

Sir Sam

11-04-2017 01:40 PM

Old post quoted:

Quote:

Originally Posted by Sir Sam

Quote:

Originally Posted by impeesia (Post 984554)

updates?

Well peese got me thinking today that maybe I should get back to work. So I started thinking about what I needed to do next which is to get the springs back under it so I can move on with fabbing up the tranny mount.

Well I got to thinking and decided that the D30 is just too weak of an axle to put under the front end with 30.5" tires, so I decided to put a JK Dana 44 front under it. Quick search of craigslist and I went and picked up the cheapest one I could find at $300.

Its missing the passenger side knuckle and the brakes, I will either replace everything thats missing and go back to JK specs, replace just the pass high steer knuckle and try to use D30 unit bearings, or put on WJ high steer knuckles and brakes(cheapest option thus far and keeps the 5x4.5 pattern)

And now I will probably get a 8.8 with 4.10s and LSD for the rear, which is my ideal setup, selectable locker in the front, LSD in the rear. I'll top it off with a TJ locker switch and have everything nice and factory like I like.

http://colorado4wheel.com/images/1988_MJ/MJ219.jpg
http://colorado4wheel.com/images/1988_MJ/MJ220.jpg

Sir Sam

11-04-2017 01:41 PM

old post quoted:

Quote:

Originally Posted by Sir Sam

Quote:

Originally Posted by MBood82 (Post 1136438)

It's been over a year, what's the status?

Sir Sam

11-04-2017 01:42 PM

old post quoted:

Quote:

Originally Posted by Sir Sam

This is the 96- steering column hole:
http://colorado4wheel.com/images/1988_MJ/MJ236.jpg

This the 97+ steering column hole, it needs to to cutout and moved obviously. Not exactly sure how I will go about that.
http://colorado4wheel.com/images/1988_MJ/MJ237.jpg

Here you can see that the newer C101 plug hole, what I will probably do it cutout the donor shape and then use the bolt holes in the older plug to hold the plate in place.
http://colorado4wheel.com/images/1988_MJ/MJ238.jpg
http://colorado4wheel.com/images/1988_MJ/MJ239.jpg

This is the older style steering column bracket, it will need to but cutout and the new one(below) welded in.
http://colorado4wheel.com/images/1988_MJ/MJ240.jpg
http://colorado4wheel.com/images/1988_MJ/MJ241.jpg

Here you can see the older style heater core hole is a little different, but it'll work.
http://colorado4wheel.com/images/1988_MJ/MJ242.jpg
http://colorado4wheel.com/images/1988_MJ/MJ243.jpg

Here you can see the upper dash bolt points are different, not sure what to do about those.
http://colorado4wheel.com/images/1988_MJ/MJ244.jpg
http://colorado4wheel.com/images/1988_MJ/MJ245.jpg

This is the older side mount bracket studs/bolt holes, the newer style is below, as you can see there are a fair amount of differences.
http://colorado4wheel.com/images/1988_MJ/MJ246.jpg
http://colorado4wheel.com/images/1988_MJ/MJ247.jpg

This is the older style door post latch, this is a little tricky but can be dealt with fairly easily.
http://colorado4wheel.com/images/1988_MJ/MJ248.jpg
http://colorado4wheel.com/images/1988_MJ/MJ249.jpg

And this is where I think I will mount the filter head:
http://colorado4wheel.com/images/1988_MJ/MJ250.jpg

I'm not sure why but I have a filter head with different banjo fittings on it, which won't work in my configuration, so the bent stockers are perfect.
http://colorado4wheel.com/images/1988_MJ/MJ251.jpg

Sir Sam

11-04-2017 01:43 PM

old post quoted:

Quote:

Originally Posted by Sir Sam

Steering column/dash bracket cutoff:
http://colorado4wheel.com/images/1988_MJ/MJ253.jpg
http://colorado4wheel.com/images/1988_MJ/MJ254.jpg

Lets do this:
http://colorado4wheel.com/images/1988_MJ/MJ255.jpg

Passenger side bracket welded on(the thin stuff at the top was a *****)
http://colorado4wheel.com/images/1988_MJ/MJ256.jpg

I got the drivers side partially welded on then tossed the dash in place to make sure I had measured the right place to weld the brackets on. Looks good to me, dash sits in place like it should.
http://colorado4wheel.com/images/1988_MJ/MJ257.jpg

Sir Sam

11-04-2017 01:43 PM

old post quoted:

Quote:

Originally Posted by Sir Sam

Got the steering column bracket in place, modded it to accept one of the existing studs and then welded one from the donor vehicle in place on the side.

http://colorado4wheel.com/images/1988_MJ/MJ258.jpg

Then I got the lower pivot hole welded in, cut off the factory nut from the donor then drilled a hole and welded the plate in. Still need to do the passenger side.

http://colorado4wheel.com/images/1988_MJ/MJ260.jpg

As you can see here two of the upper dash bolt holes don't line up, I think I'm going to weld a tab to the existing smaller lip and then drill a hole and move the threaded clip in place, then just use a large washer on the small bolt, this needs to be done on both sides.

http://colorado4wheel.com/images/1988_MJ/MJ259.jpg

Sir Sam

11-04-2017 01:44 PM

old post quoted:

Quote:

Originally Posted by Sir Sam

Got a shell for the MJ, its a brahma which means its kinda cheap, maybe in the future if I find a nice leer that I like I will upgrade, but for now this is fine by me.
http://colorado4wheel.com/images/1988_MJ/MJ271.jpg
http://colorado4wheel.com/images/1988_MJ/MJ272.jpg
http://colorado4wheel.com/images/1988_MJ/MJ273.jpg
http://colorado4wheel.com/images/1988_MJ/MJ274.jpg

The holy grail of MJ 97+ door panels:
http://colorado4wheel.com/images/1988_MJ/MJ275.jpg

Scored a set of seats from a 2 door......the seats themselves are pretty much junk, but they have the tilt mechanisms which can be installed into just about every other jeep seat(could install them in heated leather seats for example).
http://colorado4wheel.com/images/1988_MJ/MJ276.jpg

Sir Sam

11-04-2017 01:47 PM

I got a wildernest topper last year in august of 2017. And then finally got rid of the other shell on CL. Turns out the old one fit a longbed toyota truck perfect.

http://colorado4wheel.com/images/1988_MJ/IMG_9418.JPG
http://colorado4wheel.com/images/1988_MJ/IMG_9419.JPG
http://colorado4wheel.com/images/1988_MJ/IMG_9421.JPG

Sir Sam

11-04-2017 01:52 PM

New as of 3-NOV-2017:

I ordered a pair of metric ton leaf springs with ~3" or so of lift. Took a long damm time to come in but they finally arrived last night.

I have a set of ruff stuff SUA perches that I will use to mount these up to a KJ 8.25 from my 05 parts CRD.

http://www.ruffstuffspecialties.com/...DEAV-WIYP.html

The 8.25 I am using has a limited slip and 3.73s which is a good match for the CRD powerband.

http://colorado4wheel.com/images/1988_MJ/IMG_1172.JPG

JEEPJERK

11-04-2017 05:06 PM

Cool stuff...but your welding does suck. Buy a wire welder.

6DoF	11-06-2017 08:24 AM

holy crap! game on

FUBAR

11-06-2017 08:28 AM

You're taking this to a whole different level. I admire the time, patience and detail in this project. Kudos to you.

Cobound

11-07-2017 12:08 PM

Quote:

Originally Posted by FUBAR (Post 2567)

You're taking this to a whole different level. I admire the time, patience and detail in this project. Kudos to you.

Yeah, no kidding! People that question why custom builds cost so much, what goes into them...need to see build threads like this to appreciate them.

Research. Parts acquisition. Labor, list goes on...all, includingSam's welding skills, are being highlighted here!

Keep the updates coming!!

nblehm

11-09-2017 01:07 PM

Man, I tried but that front end is just not for me.

Cobound

11-09-2017 01:13 PM

Quote:

Originally Posted by nblehm (Post 2730)

Man, I tried but that front end is just not for me.

I prefer the '97+ fronts myself, but I can appreciate this being different.

B

Sir Sam

11-14-2017 06:14 PM

Quote:

Originally Posted by Cobound (Post 2734)

I prefer the '97+ fronts myself, but I can appreciate this being different.

B

Like I said back in the day, I wasn't 100% on it untill I saw it in person. I like the 97+ front, but this looks good and its interesting to have something that is still aesthetically pleasing and different.

Cobound

11-20-2017 10:46 AM

:thumbsup:

Sir Sam

01-16-2018 08:44 PM

Rolled the MJ into the garage and started prepping the KJ axle, got the KJ brackets - lower control arm, shock mount, and spring pad cutoff, and I am half done grinding the tube smooth.

Brackets to cutoff:

http://colorado4wheel.com/images/1988_MJ/IMG_1356.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1353.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1354.JPG

Spring pad cleaned up:

http://colorado4wheel.com/images/1988_MJ/IMG_1361.JPG

Everything cutoff:

http://colorado4wheel.com/images/1988_MJ/IMG_1362.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1363.JPG

Sir Sam

01-16-2018 09:18 PM

In preparation for installing the axle I sprayed the leaf springs. They were basically bare steel, or one step above it. So I prepped them by cleaning with Acetone and a microfiber rag. I had a ton of high temp rustoleum black around so I used that, hit the leaves with a bunch of coats of. Might not be the best prep or cleanup or even paint for the long term, but its gotta be better than bare and I'll its under the jeep anyway.

http://colorado4wheel.com/images/1988_MJ/IMG_1344.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1345.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1346.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1349.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1351.JPG

http://colorado4wheel.com/images/1988_MJ/IMG_1352.JPG

All times are GMT -5. The time now is 06:54 PM.

Page 2 of 7

Last »

Show 40 post(s) from this thread on one page